Contact

Sir. Swagatam, you are correct to say when an inductor be it air core, ferrite core or spiral wound bifilar or multifilar or even just a length of rubber coated wire etc. Hits it Resonant Frequency, it Lenz effect would drop to Zero. Yes, you are correct. I have seen that happens. BUT YOU ARE HEAVILY WRONG TO say such state of an inductor does not gives way to Overunity or free Energy WHEN IT IS EVEN AT THAT STATE THAT AN INDUCTOR BECOMES a portal or TAPWAY into the Unlimited Electromagnetic Force Of The Earth which is the Ambient.
When at resonance, the Back Electromagnetic Force Becomes Useful Energy which must be forwarded via a Calculated Resitor(Time Constant Formular T=RC) into the Positive plate of an High Capacitance DC Capacitor using High Voltage High Frequency Diode(s). The negative place of the capacitor must be connected to an Avramenko Plug which are made of 2 diodes in Series. The said A.V.M.P would then be connected to an Earthed Tuned Step-down Transformer to gain High Current Low Voltage.
To get Overunity this way and to be able to charge High Capacitance Capacitors in a Jiffy, you must use Radio Frequency.
The Air Is the free voltage provider while the Earthcrust, with it massive Silicon STORAGE, is the Current provider. So what you need do is to harvest the back e.m.f in a One Wire fashion(there must be no return wire back into the generator or the inductor generating the Back E.M,F at RESONANCE STATE.)

Now the Radio frequency you select must be the Natural Resonant Frequency of the length of wire in feet you would use to wind your Back emf generator which must be Pulsed at High frequency. So assuming you select 40Khz as you running frequency, just divide 40000 Hertz by 998. The number you get in feet must be the length of wire you must Cut and use to made your coil be it in spiral or cylindrical.
You can even make the coil as Primary while you wind lots of thinner rubber coated multi-srand wire underneath the primary to Multiply the voltage at your selected Natural sesonant frequency of the Primary Wire Length which must be thicker than the Secondary wire. You must wind all layers of Secondary in Same direction as the primary. If you start from left to RIGTH, you must complete the overlapping layers of the Secondaries in same direction as well as the primary.
Now if you make it this way, you have just made a Step-Up Transformer. But you must use A Time-Constant Formular Calculated Resitor( formular: T=L/R T is the frequency you want to use the Resitor to tune the Secondary ending Inductance to) to collect the BACK EMF FROM THE PRIMARY into the secondary at the Drain point of the N-Channel Mosfet which is being exactly driven at 40Khz as calculated. You can select higher frequency but not lower than 20Khz. You must just make sure the frequency is Natural to the length of wire in feet of the primary of your Step-Up Overunity Transformer.

But Why Do You Need To Step The Voltage?
First when voltage exists, it does not exist alone. Current is somewhere lurking in darkness. So to make that darkness disappear to see the Current, you need RESONANCE, High Capacitance and Robust Earthed Point.
Your Primary and Secondary windings must be Oscillating at same frequency. The DC Capacitor Banks must also be in agreement with the driving frequency. The higher the Capacitance of your Capacitor Bank which acts as Massive Dam of High Current Holding or Sea Of High Current, The High the Total Output Wattage. But you must also dig deep into the earth or soil. I recommend minimum of 6 feet. Use Thick Copper Plate of at least 1cm and very wide as you can get for your Earthing. My Earthing is as deep as 10feet and I was lucky to meet a Rock(Haven Of Current Donating Silicon) at the Bottom where I place my Thick Gauge Output Cable Attached Thich Copper Plate. After Placing my Copper Plate on the rock, I pour my industrial salt, granulated broken bottles and some other materials there to Make the Spot A Super Current Generator Waiting To Be Tapped Trough One Wire Avramenko Plug attached Step-Down Transformer.

So you step up and later step down to get massive Killowatts to Giga Watts of Electric Power Unlimitedly.Infact if you can make your Step-Up Transformer secondary windings into a Multi-Filar winding or overlapping Spirawindings which would be connected in series, you may not not intermediary Current Damming High Capacitance DC Capacitors because Of the secondary would have Brutally High Inductance which would makes is Generate Massive Wattage on it own which can then be step down directly via the EpRobustly Earthed Step-Down Transformer.
When you wants to step down, you can tune the step down trafo to 60Hertzs or just tune it to 40KHZ and use pi filter or other methods to get rid of High Frequency and therby obtain say 12V or 24V or 48V or 98VDC etc. to Run your DC to AC Inverter.

This system is real and working. The current and voltage in the Air and Ground or Earth is there for any Human born and yet to be born, TO T.A.P unlimitedly forever when you know how to. And the first Step is RESONANCE.

Hello I’m trying to build feedback for SG3525 with octocoupler and TL431 with variable resistor how do I connect this to my high voltage side there’s no auxiliary output just direct 300v

2 X 12 Lead acid batteries in series 24 volts for charging voltage should be around 32 volts

thank you Mr.swagatam. I will be happy to receive the same

Many thanks Swagatam for a quick response.
I have come across similar problems with stated max values in datasheets, which is a bit misleading. This is something like 8% less than stated (theoretical value).
I will try a few changes to confirm practical limits.
1 – Revert back to the minimist component count and values.
2 – Check oscilloscope display settings for peak readings or whatever (V_pp, V_p, V_max, V_min,_avg, V_rms)
3 – Try using a more powerful 5v supply source.

Respected Sir,
Thanks for your response and the valuable ideas.
Sir, since I don’t have sufficient time to get through the complex circuit and design the diagram, can you please share some assured readily available circuit boards in market.