• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Hire Me | Contact | Calculators-online
You are here: Home / Voltage Control and Protection / Passive Power Factor Correction (PFC) Calculator

Passive Power Factor Correction (PFC) Calculator

Last Updated on April 15, 2026 by Swagatam 8 Comments

This passive PFC calculator does not use any MOSFET or PWM or switching frequency. It only uses 50 Hz mains and it only works with inductors and capacitors, so the only thing that matters is the reactance of the inductor and the reactance of the capacitor at the mains frequency. That is why the calculator uses only AC voltage, AC frequency, capacitor value and inductor value.

Table of Contents
  • Simple Passive PFC Calculator
  • Circuit Diagram
  • How it Works
    • Function of Bridge Rectifier
    • Function of Inductor
    • Function of Capacitor
    • Conclusion
    • Manual Calculations using Formulas to Counter Check Calculator Output
Calculator by homemade-circuits.com

Simple Passive PFC Calculator









Circuit Diagram

How it Works

We see that this PFC diagram is showing the most simple passive PFC idea, so the mains AC is entering from the left side and then it is going inside a full bridge rectifier.

Function of Bridge Rectifier

We know that this bridge rectifier is taking the AC and converting it into pulsating DC, so when the AC goes positive then two diodes conduct and when AC goes negative then the other two diodes conduct, so you always get a unidirectional DC at the right side of the bridge.

Function of Inductor

Then we see that after this bridge rectifier there is one big inductor connected in series with the output line, so we understand that this inductor is the actual PFC element.

We know that when the current tries to suddenly rise and fall due to the pulsating rectified waveform then the inductor opposes this sudden change.

So now what happens is that the inductor tries to slow down the current ripple and tries to make the current waveform more smooth and more sinusoidal, so the current waveform becomes more in phase with the AC voltage.

That is why this is called power factor correction. The inductor forces the current to rise and fall slowly so it becomes closer to the voltage shape.

Function of Capacitor

Then we see at the end there is one big capacitor connected to ground from the positive line.

We know that this capacitor is only for filtering and energy storage, so when the load is taking power then the capacitor gives the required stable DC and when the bridge rectifier pulses come then the capacitor gets charged and maintains the voltage, so the inductor smooths the current and the capacitor smooths the voltage.

Conclusion

So we can say that the AC first becomes pulsating DC through the bridge, then the inductor shapes the current wave to make it slow and sinusoidal like, then the capacitor filters the final DC and supplies the load.

It means that this is the most basic passive PFC where we only use the natural property of the inductor to improve power factor without any PWM or MOSFET control.

Manual Calculations using Formulas to Counter Check Calculator Output

  1. Vpeak (mains peak)
    Vrms = 220.00 V
    sqrt(2) = 1.4142135623730951
    Vpeak = Vrms * sqrt(2) = 220 * 1.4142135623730951 = 311.127 (rounded of) V
    (keep as 311.127105721081 V for precision)
  2. DC bus used (auto method in calculator)
    We used diode drops ≈ 2 × 1.1 V = 2.2 V
    Vbus = Vpeak − 2.2 = 311.127105721081 − 2.2 = 308.927105721081 V
  3. DC load current I_dc = Pout / Vbus
    Pout = 3000 W
    I_dc = 3000 / 308.927105721081
    Divide step by step:
    3000 ÷ 308.927105721081 = 9.711 (rounded) A
    More precisely I_dc = 9.711012... A.... displayed as 9.71 A.
  4. Required total bulk capacitance (for peak-to-peak ripple ΔV = 5 V)
    Formula: C_total = I_dc / (2 · fline · ΔV)
    fline = 50 Hz, ΔV = 5 V
    Denominator = 2 * 50 * 5 = 500
    C_total = 9.711012... / 500 = 0.019422024... F
    Convert to µF: 0.019422024 * 1e6 = 19,422.024 µF
    Rounded = 19,425 µF (our calculator showed 19,425 µF)...... so matches within rounding.
  5. Required PFC inductor (series choke) for peak charge limit I_charge = 20 A
    Xpfc = Vpeak / I_charge = 311.127105721081 / 20 = 15.55635528605405 Ω
    Lpfc = Xpfc / (2π fline) = 15.55635528605405 / (2 * π * 50)
    2π×50 = 314.1592653589793
    Lpfc = 15.55635528605405 / 314.1592653589793 = 0.049526 (H)
    Convert to mH: 0.049526 * 1000 = 49.526 mH
    Rounded = 49.51 mH (our calculator showed 49.51 mH) — so it matches.

practical rounded numbers

  • Vpeak ≈ 311.13 V
  • Vbus used ≈ 308.93 V
  • DC Load Current I_dc ≈ 9.71 A
  • Required total bulk capacitance ≈ 19,420 µF (≈ 19.4 mF) — our calculator 19,425 µF is fine.
  • Required series PFC inductor Lpfc ≈ 49.53 mH — our calculator 49.51 mH is fine.

Notes and quick practical tips

  • The bulk cap result ≈ 19.4kµF means use multiple caps in parallel (example 5×4700 µF @400V = 23.5kµF is a practical choice).
  • Lpfc ≈ 49.5 mH is large and heavy for 3 kW. If space/weight is a problem, use NTC/soft-start or accept higher I_charge.
  • All manually arithmetic matches exactly as calculator outputs and are correct to displayed precision.

Filed Under: Voltage Control and Protection Tagged With: Calculator, Correction, Factor, PFC, Power

About Swagatam

I am an electronics engineer and doing practical hands-on work from more than 15 years now. Building real circuits, testing them and also making PCB layouts by myself. I really love doing all these things like inventing something new, designing electronics and also helping other people like hobby guys who want to make their own cool circuits at home.

And that is the main reason why I started this website homemade-circuits.com, to share different types of circuit ideas..

If you are having any kind of doubt or question related to circuits then just write down your question in the comment box below, I am like always checking, so I guarantee I will reply you for sure!

Previous Post: « Make this Single MOSFET Solid-State Relay SSR circuit
Next Post: PFC (Power Factor Correction) Calculator Tool: 3kW »

Reader Interactions

Questions & Answers

Total Posts: 8
Newest Oldest
ROBERT Paterson
November 6, 2026 • 2 weeks ago #214635

Hi Swagatam
Thanks for all your help, as you say harmonics may play a part. It was only a interest but it’s not worth pursuing due to small loads, harmonics etc.
Thanks for all your input i will find other projects.

Bob P

Reply
SwagatamAdmin
November 7, 2026 • 2 weeks ago #214706

Hi Bob,

You’re most welcome! It was a pleasure discussing this with you. All the best with your future projects, and feel free to drop by anytime!

Reply
ROBERT Paterson
November 5, 2026 • 2 weeks ago #214570

Hi Swagatam
Maybe a factor i never mentioned is, apart from the led lights there is 6 – 8 watt emergency lights which have small transformers as you know, does this help ? Using a LCR meter

The readings are L-620millie henry C – 6microfarad R 231ohms Does this help?

Thanks Bob P

Reply
SwagatamAdmin
November 6, 2026 • 2 weeks ago #214604

Hi Bob,
Yes, that helps. Your LCR meter readings show that the lighting circuit has both inductive and capacitive components. However these readings alone do not tell us the exact compensation required for the complete load.
Based on your earlier calculated capacitive reactance (Xc) of 117.80 ohms, a 375 mH inductor would theoretically provide an equal inductive reactance (XL) at 50 Hz and cancel the fundamental capacitive effect.
However the actual PF correction may vary depending on the complete load and harmonic distortion.

Reply
ROBERT Paterson
November 4, 2026 • 2 weeks ago #214536

Hi Swagatam

I can confirm the 117.80 is the calculated xc – mains voltage is 240v – stated wattage is 244 watts – pf 0.68 – app power 169.72 va – real power 115.5 watts Bob P

Reply
SwagatamAdmin
November 5, 2026 • 2 weeks ago #214562

Hi Bob,

Thanks for the details.

I have checked your figures, and there seems to be a small discrepancy that I would like to clarify before suggesting the inductor. If 117.80 ohms is the actual capacitive reactance across 240V, then capacitive current would be approximately 2.04A, representing around 489 VAR. However your stated real power of 115.5W and apparent power of 169.72VA indicate a considerably different reactive power. Could you tell me how you calculated the 117.80 ohms value? Also is your 0.68 PF reading obtained from a power meter measuring true PF. I just want to make sure we calculate the correct compensation value rather than suggest an unsuitable inductor.

Reply
ROBERT Paterson
November 2, 2026 • 3 weeks ago #214463

Hi my name is Robert Paterson

I have LED lights which have a poor PF due to a capacitive load i have calculated the Qc it is 117.80 ohms, can you tell me what size of inductor do i need to correct this to near unity.

Thanks Bob P.

Reply
SwagatamAdmin
November 2, 2026 • 3 weeks ago #214466

Hi Bob,
If your calculated value of 117.80 ohms represents the actual capacitive reactance (Xc) of the complete LED load, then theoretically you will need a parallel inductor having an equal inductive reactance (XL) of 117.80 ohms to cancel the fundamental reactive current.
For 50 Hz mains, the required inductance will be approximately 375 mH, while for 60 Hz mains it will be approximately 312.5 mH. The inductor must be rated to handle the continuous reactive current without overheating or core saturation. Also please note that this correction may not bring the overall power factor close to unity because LED drivers can produce harmonic distortion which a simple parallel inductor cannot eliminate. There can also be unwanted resonance between the inductor and the capacitors inside the LED drivers.

Before suggesting a final inductor, could you please confirm whether 117.80 ohms is your calculated capacitive reactance (Xc), along with your mains voltage, frequency and total LED wattage?

Reply

Need Help? Please Leave a Comment! We value your input—Kindly keep it relevant to the above topic! Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

Categories

  • Arduino Projects (95)
  • Audio and Amplifier Projects (134)
  • Automation Projects (18)
  • Automobile Electronics (104)
  • Battery Charger Circuits (90)
  • Datasheets and Components (109)
  • Electronics Theory (153)
  • Energy from Magnets and Earth (43)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (20)
  • Health related Projects (27)
  • Home Electrical Circuits (13)
  • Indicator Circuits (16)
  • Inverter Circuits (112)
  • Lamps and Lights (183)
  • Meters and Testers (72)
  • Mini Projects (28)
  • Motor Controller (68)
  • Oscillator Circuits (30)
  • Pets and Pests (15)
  • Power Supply Circuits (92)
  • Remote Control Circuits (50)
  • Security and Alarm (65)
  • Sensors and Detectors (122)
  • SMPS and Converters (52)
  • Solar Controller Circuits (63)
  • Temperature Controllers (44)
  • Timer and Delay Relay (51)
  • Voltage Control and Protection (44)
  • Water Controller (37)
  • Wireless Circuits (31)

People also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |

My YouTube Channel

Circuit Simulator: Draw and Simulate Schematics

circuit simulator image

Subscribe to get New Circuits in your Email

Other Links

  • Privacy Policy
  • Cookie Policy
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap

Recent Comments

  • Swagatam on GSR Sensor Circuit for Biofeedback Measurements
  • Swagatam on Understanding Triac Snubber Network Calculations
  • Bol Tune on Understanding Triac Snubber Network Calculations
  • Tannaberton Abacrombie on GSR Sensor Circuit for Biofeedback Measurements
  • Swagatam on Understanding Triac Snubber Network Calculations

Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Stack Exchange
  • Linkedin

Calculators

  • ZVS Induction Heater + Tank Calculator Tool
  • Zener Diode Calculator
  • Wire Current and Thickness Calculator (Ampacity Calculator)
  • Resistive Voltage Divider Calculator
  • Transistor Base Resistor Calculator
  • Transistor Astable Multivibrator Calculator
  • TL431 Calculator
  • Solar Panel, Inverter, Battery Calculator
  • Ferrite Core Air Gap Calculator Tool
  • Parallel MOSFET Calculator Tool: How to Connect MOSFETs in Parallel Safely
  • LC Resonance Calculator for EV Battery Charger Circuits
  • LED String Series Resistor Calculator
  • PFC (Power Factor Correction) Calculator Tool: 3kW
  • Passive Power Factor Correction (PFC) Calculator
  • LM567 IC Calculator Tool
  • SMPS Flyback Boost Converter Calculator
  • Shunt Resistor Calculator for Ammeters
  • SCR and Triac Gate Resistor Calculator
  • Battery Back up Time Calculator
  • Boost Converter Calculator (Non-Isolated)
  • Bootstrap Capacitor Calculator
  • Buck Converter Calculator
  • Buck-Boost Converter Calculator
  • Capacitance Reactance Calculator
  • DCM Flyback Transformer & Wire Gauge Wire Size Calculator Tool
  • Filter Capacitor Calculator
  • IC 4047 Calculator (Frequency and PWM)
  • IC 4060 Calculator
  • IC 555 Astable Calculator
  • IC 555 Monostable Calculator
  • IC SG3525, SG3524 Calculator
  • Inductance Calculator
  • Induction Heater Inductor and Resonant Frequency Calculator
  • Induction Heater Work Coil Calculator
  • Inverter LC Filter Calculator
  • LC Resonance Calculator
  • LED Current Calculator
  • LM317, LM338, LM396 Calculator
  • NAND/NOT Gate RC Values Calculator
  • NOT, NAND Gate Frequency Calculator
  • Notch Filter Calculator Tool
  • Ohm’s Law Calculator
  • Phase Angle Phase Shift Calculator
  • Power Factor (PF) Calculator
  • RC Filter Calculator
  • Reactance Calculator
  • Sine Table Calculator for SPWM Arduino Code
  • Small Signal Transistor(BJT) and Diode Quick Datasheet
  • SMPS Calculator for Toroidal Ferrite Transformers
  • SMPS Flyback Transformer Calculator – Design by Target Duty Cycle
  • TL431 Calculator
  • Op-Amp Hysteresis Resistor Calculator

© 2026 · Swagatam Innovations