• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Contact | Calculators-online
You are here: Home / Transmitter Circuits / Make a Walkie Talkie Circuit using FM Radio

Make a Walkie Talkie Circuit using FM Radio

Last Updated on February 27, 2020 by Swagatam 59 Comments

In this post I have explained how to make a simple homemade walkie talkie circuit using ordinary FM transmitters and FM radios. It's a perfectly tested design by me.

Table of Contents
  • Overview
  • High Range Design
  • Circuit Diagram
  • How the Transmitter Works.
  • Using an FM Radio as the Walkie Talkie Receiver (Rx)
  • How to Tune and Test The Walkie Talkie Pairs
  • Parts List for the above shown transmitter
  • PCB Design

I could talk with my nephew who stays on first floor through a pair of these transmitters with crystal clear transmission.

warning message: electricity is dangerous, proceed with caution
walkie talkie using FM radio

Overview

In one of my earlier post I will comprehensively explained the making of a compact walkie talkie design, however I found that many new hobbyists and school students found the design difficult to adjust and succeed due to its rather complex and the associated strict parameters,

In this post we try to design a walkie talkie using discrete transmitter modules and then tune them to different frequencies such that the units are able transmit and exchange the conversation across both the sides without interfering with their own receive modules.

For the FM transmitters we select the design which was earlier discussed in our wireless speaker circuit, the main reason being its ability to produce high power output, which enables the circuit to transmit the data over much longer distances compared to the other smaller FM transmitters designs.


Want to learn how to build a small transceiver circuit? The following post will walk you through all the details:

Mini Transceiver


High Range Design

As you can see the design is different from the usual single transistor concepts. Here the design incorporates a 3 transistor design along with a center tap antenna coil. This enhances the power output of the transmitter to a great extent, approximately 4 times more than the single transistor version.

With this special patented design you can enjoy communicating with your friends in your multistorey apartment, across the highest number of floors.

The minimum distance this unit can cover is 50 to 100 meters.

The range of a single transistor circuit cannot be over 30 meters. Check it yourself!

The main objective here is to get a reasonable distance of wireless communication facility.

Circuit Diagram

Transmitter 2

How the Transmitter Works.

The Transmitters: First you will have to construct two of these identical transmitter circuits as shown below:

The operating principle of this powerful little transmitter can be understood from the following points:

The MIC converts the voice signals into electrical signals which is further amplified into high amplitude low current signals by T1.

This amplified signal is fed to the base of T2 which basically forms a frequency generator stage with the help of L1, C4, C5 and C3. Together this stage forms a regenerative oscillator which resonates in the range of 50 to 200MHz depending on the setting of the relevant LC tank components settings and values.

The amplified voice signals from T1 collector gets effectively modulated over the T2 high frequency carriers waves and this modulated signal is applied to the base of T3 for enriching it with high current.

T3 basically ensures that the modulated voice signals become significantly powerful with current, and is able to be transmitted to much longer distances with the help of an appropriate antenna.

The antenna does not need to be anything special, rather an ordinary 2 feet long flexible wire will be quite enough to enable the transmission to reach over 200 meter distance.

Along with these two transmitters you will also need a couple of FM receiver units or simply FM radios, so that the transmitted signals can be received by the respective radios and a conversation over the two sides can be completed.

Thus we basically have two sets of transmitter/radio through which two individuals are able to exchange their thoughts by speaking over the respective MIC inputs.

Each of the Tx/Rx sets must have mismatched frequency while the opposite side Tx/Rx must have accurately matched frequency response, in other words the opposite side Rx/Tx must be optimally tuned with a given frequency value which must be sufficiently different from the tuned frequency value of the other opposite Tx/Rx pair.

For example if one opposite Tx/Rx pair is tuned at 90MHz, the other could be tuned at 100MHz frequency just to make sure that each of the walkie talkie unit doesn't interfere with their own set frequency value.

Using an FM Radio as the Walkie Talkie Receiver (Rx)

walkietalkie 1

The radio could be any type depending on the user's choice, but preferably it must have a convenient frequency adjustment button such as a knob or a up/down keys.

Your smart phone FM radio would also work but the range would be significantly less than conventional radio having a telescopic antenna. If you intend to operate the units for a room to room conversation then probably your phone would do the job as the receiver,

How to Tune and Test The Walkie Talkie Pairs

First make sure that your transmitter is correctly built and is actually transmitting the signals. To do this keep an FM radio at around 2 meters away from the Tx circuit, switch ON the Tx and the radio, and start adjusting the frequency knob of the radio until you suddenly find a "dead" spot on the band.

Now tapping lightly on the MIC should generate a thudding sound on the radio speaker, confirming the transmission from the Tx unit.

After this, keep increasing the distance between the Tx and the radio and finally try finding the maximum possible distance that the units are able to interact optimally. This may be done by some trial and error and by some skillful fine tuning of the adjustments of the two counterparts.

Repeat the same for the other Tx/Radio pair and this will complete your homemade FM walkie talkie circuit.

Now it's just about keeping the oppositely tuned units across the two sides from where the conversation needs to be done, and then with some more adjustments you can finally get the conversation going with this simple homemade equipment.

If you have any doubts, please feel free to share them through your comments.

Parts List for the above shown transmitter

  • R1 =1M,
  • R2 = 2K2,
  • R3 = 470 Ohms,
  • R4 = 39K,
  • R5 = 470 Ohms,
  • R6 = 4k7
  • C1 = 0.1 uF,
  • C2 = 4.7 uF,
  • C3, C6 = 0.001uF,
  • C4 = 3.3pF,
  • C5 = 10pF,
  • L1 = It is a 7 turn coil made using 1 mm super enameled copper wire, having 6 mm diameter. The center tap is taken from 1st turn as shown below.
  • T1, T2 = BC547B,
  • T3 = 2N2907B
  • MIC= electret MIC

L1 Coil Design

L1

If you are having any confusions regarding the construction of this project contact me immediately, I'll help you through until your project is completed.

PCB Design

The PCB design for the proposed FM radio based walkie talkie circuit can be witnessed below:

Bug5 pcb h
single transistor walkie talkie circuit

As you can see, the antenna coil is designed on the PCB itself, through a spirally laid track layout, having the exact required embedded inductance. Thus the circuit becomes truly compact as it does not depend on the traditional, cumbersome, manually wound copper coil.

The supply being 9V, it works with extra power ensuring that the conversation is distinctly clear even at distances over 150 meters, which other similar transmitter would simply fail to accomplish.

Make sure to use a 1 meter long flexible wire for the antenna, to get a distortion free walkie talkie experience.

You'll also like:

  • 1.  1.5 watt Transmitter Circuit Diagram
  • 2.  Making a Wireless Doorbell Circuit
  • 3.  Wireless Mobile Phone Charger Circuit
  • 4.  Simple Walkie Talkie Circuit
  • 5.  Laser Communicator Circuit – Send, Receive Data with Laser
  • 6.  2 Meter Ham Radio Transmitter Circuit

About Swagatam

I am an electronics engineer with over 15 years of hands-on experience. I am passionate about inventing, designing electronic circuits and PCBs, and helping hobbyists bring their projects to life. That is why I founded homemade-circuits.com, a website where I share innovative circuit ideas and tutorials. Have a circuit related question? Leave a comment.... I guarantee a reply!

Previous Post: « 27 MHz Transmitter Circuit – 10 Km Range
Next Post: How Blocking Oscillator Works »

Reader Interactions

Comments

  1. Rashid abdallah says

    November 16, 2024 at 5:44 pm

    please create a circuit for FM radio receiver with a knob for searching stations that can be using 3v

    Reply
    • Swagatam says

      November 17, 2024 at 8:32 am

      If it is possible, I will surely try to design it soon, and let you know.

      Reply
  2. JOBAYER AL HASAN says

    August 23, 2024 at 6:27 pm

    I have a FM transmitter module which have an Antenna already. i bought FM analog radio which also have a Fm antenna. How can I cope up them?

    Reply
    • Swagatam says

      August 24, 2024 at 8:51 am

      JOBAYER, are you trying to build a walkie-talkie using a separate FM radio and an FM transmitter?

      Reply
  3. m.r says

    June 18, 2024 at 2:06 pm

    hi Mr Swagatam.
    I made it and it worked properly with 15v supply (not 9v supply). as you said the range is better than simple transmitters but T3 is getting hot.
    can i use BD136 and change the bios in order to get higher current and enrich more the transmitting signal.
    and can you tell me the formula about calculate the LC tank frequency.
    thanks a lot for your support.

    Reply
    • Swagatam says

      June 18, 2024 at 5:33 pm

      Hi, M.R
      The 2N2907 should not heat up with a 330 ohm or 470 ohm collector/ground resistor.
      In fact you can even use a BC557 without any heating up.
      If you want to use BD136, you can try it.

      The formula for calculating LC tank frequency is:

      f = 1 / (2π√(LC))

      where:

      f is the resonant frequency in Hertz (Hz)
      L is the inductance in Henries (H)
      C is the capacitance in Farads (F)
      π (pi) is a mathematical constant approximately equal to 3.14159

      Reply
      • m.r says

        June 18, 2024 at 7:05 pm

        In this circuit C should be calculated between (C4 and C5) or (C4 and C5 and C3)?

        Reply
        • Swagatam says

          June 18, 2024 at 10:07 pm

          Only C5…

          Reply
  4. m.r says

    June 13, 2024 at 1:41 pm

    hi sir why did you mention two different value of parts I mean in schematic and pcb desingn.
    which of them is true for example in sch we have resistor 470 ohm but in pcb 330 ohm or in sch we don’t have capacitor 12pf and 2.7 pf but in pcb design we have.
    thanks for your help.

    Reply
    • Swagatam says

      June 13, 2024 at 2:05 pm

      Hi m.r, actually both the versions will work, but I would recommend you to follow what’s given in the PCB design, which is easier to implement.

      Reply
      • m.r says

        June 13, 2024 at 3:17 pm

        thanks for your answer but witch of them can cover more distance and how much?

        Reply
        • Swagatam says

          June 13, 2024 at 5:39 pm

          The slight difference in component values does not affect the range, the range will remain within 150 meters regardless of the part difference.

          Reply
  5. Aladin jlassi says

    May 20, 2024 at 12:40 am

    what does mean R2=2K2 and R4=4K7 ?? what are the values of the following resistor ? thank you at first .

    Reply
    • Swagatam says

      May 20, 2024 at 6:46 am

      2k2 = 2.2k
      4k7 = 4.7k

      Reply
  6. Yashwin P says

    January 18, 2024 at 9:22 pm

    Sir you mentioned two identical circuits need to be built…fine but how do we set tx 2 circuit at some other frequency than the one used by tx 1 circuit

    Reply
    • Swagatam says

      January 19, 2024 at 8:55 am

      Hi Yashwin,
      You can set the tx1 and tx2 frequencies using an FM radio. Set the frequencies such that they are received by the radio at two different locations on the band. For example tx1 can be fixed at 95 MHz, and tx2 can be set at 101 Mhz.

      Reply
  7. Simon says

    April 27, 2023 at 6:37 pm

    Could you use this circuit for a transmitter in the 863-865 Mhz range?

    Reply
    • Swagatam says

      April 27, 2023 at 6:46 pm

      It can be probably done by reducing the L1 number of turns, or by reducing the C5 value.

      Reply
  8. :Joseph-Grant. says

    January 12, 2023 at 3:10 am

    beautiful explanations, thank you! I enjoy your projects.

    Reply
  9. Anas says

    May 15, 2022 at 6:25 pm

    Can You please tell me About L1 which material is Used Thickness of wire number of Turns Or length of Wire
    In walkie talkie using FM Radio

    Reply
    • Swagatam says

      May 16, 2022 at 9:37 am

      It is given in the parts list. Please check it.

      Reply
  10. nicolas says

    October 29, 2021 at 11:08 pm

    hi I’m Nicolas from South Africa I am really interested in learning electronics, so I would like to know don’t you have a YouTube channel where you make tutorial videos about electronics, I would like to subscribe.

    Reply
    • Swagatam says

      October 30, 2021 at 10:11 am

      Hi, I have a Youtube video channel, but there are no tutorials, only electronic experiments

      Reply
  11. Smit B says

    October 14, 2021 at 11:27 am

    How can i increase the range of this one?

    Reply
    • Swagatam says

      October 14, 2021 at 1:17 pm

      By the increasing the antenna length….

      Reply
  12. Billel BOUZIDI says

    May 29, 2021 at 11:58 pm

    Salam,
    Hi there,
    I’ve bought a walkie talkie toys for my two little girls, but they are too bad, I hope to get any help from you how to improve there electronic-circuit, and make my daughters happy.
    Thanks.

    Reply
    • Swagatam says

      May 30, 2021 at 1:10 pm

      Hi, improving the circuit can be done only if you know the whole working of the circuit, other wise it can be difficult. The external way is to increase the antenna length by adding a feet long wire to the existing antenna.

      Reply
  13. Ramanan.V says

    March 25, 2021 at 8:16 am

    Can I get PCB for this transmitter? Pls mention cost & How to order?. Thanks &Regards.

    Reply
    • Swagatam says

      March 25, 2021 at 12:31 pm

      Sorry, we don’t sell PCBs or electronic materials from this website!

      Reply
  14. Sarwana says

    November 13, 2020 at 4:20 pm

    Hello Mr.Swag my question ,can i use variabel capacitor for change C5?

    Reply
    • Swagatam says

      November 13, 2020 at 9:38 pm

      Hi Sarwana, yes you can do it

      Reply
      • Sarwana says

        November 20, 2020 at 5:27 am

        Mr.Swag , T3 = 2N2907B can change with bc557 ? Thanks

        Reply
        • Swagatam says

          November 20, 2020 at 5:17 pm

          yes you can try that!

          Reply
  15. Alyssa says

    November 7, 2020 at 9:50 pm

    Hi do you have the computations on how you have come up with this design? If yes I hope you could share them 🙂

    Reply
    • Swagatam says

      November 8, 2020 at 9:12 pm

      Hi, sorry, I do not have the calculations for this project!

      Reply
  16. mefiko says

    February 3, 2020 at 9:49 pm

    Dear inventor. .. thank you so much for your tutorials and help… my question is …is it possible to change some components to convert it to work on HAM range? Or can it be converted to a portable HAM?

    Reply
    • Swagatam says

      February 4, 2020 at 8:35 am

      Hello, sorry that’s not possible, however I have a few good HAM radio circuits which I’ll be publishing soon…so please stay tuned.

      Reply
  17. Sunshine says

    January 29, 2020 at 7:17 pm

    Good day sir…engineer I made this circuit is working but is not going far as I need….I want it go upto 10km pls help me sir thanks

    Reply
    • Swagatam says

      January 29, 2020 at 8:46 pm

      Thanks Sunshine, I am glad its working for you, however it is meant for just around 500 meters, for 10km you will need a more sophisticated design such as as this:

      https://www.homemade-circuits.com/27-mhz-am-fm-transmitter-circuit-for-citizen-band-communication/

      Reply
  18. NimrA says

    December 27, 2019 at 7:34 pm

    Is there any alternative for L1 and centre tape capacitor??

    Reply
    • Swagatam says

      December 27, 2019 at 8:43 pm

      What is so difficult in it? It is a straightforward coil. You can try the PCB track embedded coil otherwise…

      Reply
      • Nimra says

        December 27, 2019 at 9:23 pm

        Actually, I have to make schematic of this circuit for project report and proteus doesn’t allow to connect wires in the middle of any component.(L1)

        Reply
        • Swagatam says

          December 28, 2019 at 12:06 pm

          In that case you can remove the entire T3 stage and its associated components…but this may cause the range to become quite less.

          Reply
  19. Francisco says

    October 30, 2019 at 2:18 am

    Lista de peças diferentes da placa PCB. Diferenças nos transistores, capacitores com outros valores?

    Reply
  20. howtooz says

    October 10, 2019 at 7:54 pm

    Can you please make video for the connection of L1 and its center tapping?…its critical part

    Reply
    • Swagatam says

      October 10, 2019 at 7:58 pm

      It is already shown in the L1 coil design, you will have to do it exactly in the same way

      Reply
  21. Annes says

    July 17, 2019 at 5:27 pm

    Hello Swatagam,
    I’ve tried to build your circuit, but I’m having problems.
    The microphone doesn’t work at all (even when I replace it bij a stereo microphone), so I’ve connected a tone generator to the transmitter. This way I do get something of a transmission, but it is very dependant of the orientation of the antenna, and quite weak. The signal is also very much disturbed by regular radio transmissions.
    Do you have an idea what could be wrong?
    Thank you in advance from the Netherlands!

    Reply
    • Swagatam says

      July 17, 2019 at 5:52 pm

      Hello Annes, The mic should be an electret mucrophone, as given here:
      https://www.homemade-circuits.com/how-electret-microphone-works/
      this circuit has been thoroughly tested by me and for me it worked very nicely. Make sure the coil is built exactly as shown. I could transmit music upto 3rd floor using this circuit in my building. And when music is transmitted this circuit becomes even more powerful and long distant.

      If possible I’ll try to post a video soon.

      Reply
  22. Sunshine says

    May 16, 2019 at 2:32 am

    Engr. Swagatam,thanks so much. Pls I need to build a multi dual tone frequency circuit.,..or any similar circuit.
    2..I need a circuit that can record voice and replay it at any time… Pleas help thanks

    Reply
    • Swagatam says

      May 16, 2019 at 9:53 am

      For a multitone circuit, use a IC 555 astable and adjust it frequency through sa pot, or the same can be done using a 4060 IC.

      second circuit is given here:
      https://www.homemade-circuits.com/?s=voice+record

      Reply
  23. Smile says

    April 29, 2019 at 11:10 am

    how many volts are the capacitors?

    Reply
    • Swagatam says

      April 29, 2019 at 12:35 pm

      normal rating, that you get in the market for the respective categories!

      Reply
      • Swagatam says

        April 29, 2019 at 12:35 pm

        …it should be higher than 12V

        Reply
        • Smile says

          June 4, 2019 at 4:57 am

          Ok thank you, and also, what is L1 please?

          Reply
          • Swagatam says

            June 4, 2019 at 8:07 am

            I have updated the details of L1 in the article, please check it out.

            Reply
  24. Shaikh Saad says

    April 1, 2019 at 7:46 pm

    Is the circuit tested?

    Reply
    • Swagatam says

      April 1, 2019 at 8:14 pm

      tested!

      Reply
  25. Batuhan KOC says

    February 13, 2018 at 6:31 pm

    How do we have to connect c7? the connection is not shown in diagram :/

    Reply
    • Swagatam says

      February 13, 2018 at 8:48 pm

      please ignore it, it’s not there

      Reply

Need Help? Please Leave a Comment! We value your input—Kindly keep it relevant to the above topic! Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

Subscribe to New Circuit Ideas

Categories

  • Arduino Projects (87)
  • Audio and Amplifier Projects (132)
  • Automation Projects (17)
  • Automobile Electronics (101)
  • Battery Charger Circuits (83)
  • Datasheets and Components (104)
  • Electronics Theory (143)
  • Free Energy (37)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (19)
  • Health related Projects (25)
  • Home Electrical Circuits (12)
  • Indicator Circuits (14)
  • Inverter Circuits (87)
  • Lamps and Lights (142)
  • Meters and Testers (69)
  • Mini Projects (46)
  • Motor Controller (64)
  • Oscillator Circuits (27)
  • Pets and Pests (15)
  • Power Supply Circuits (108)
  • Remote Control Circuits (50)
  • Security and Alarm (64)
  • Sensors and Detectors (101)
  • Solar Controller Circuits (59)
  • Temperature Controllers (42)
  • Timer and Delay Relay (49)
  • Transmitter Circuits (29)
  • Voltage Control and Protection (37)
  • Water Controller (36)

Calculators

  • Battery Back up Time Calculator
  • Capacitance Reactance Calculator
  • IC 555 Astable Calculator
  • IC 555 Monostable Calculator
  • Inductance Calculator
  • LC Resonance Calculator
  • LM317, LM338, LM396 Calculator
  • Ohm’s Law Calculator
  • Phase Angle Phase Shift Calculator
  • Power Factor (PF) Calculator
  • Reactance Calculator
  • Transistor Astable Calculator
  • Transistor base Resistor Calculator
  • Voltage Divider Calculator
  • Wire Current Calculator
  • Zener Diode Calculator
  • Filter Capacitor Calculator
  • Buck Converter Calculator
  • Boost Converter Calculator
  • Solar Panel, Inverter, Battery Calculator
  • Wire Current Calculator
  • SMPS Transformer Calculator
  • IC SG3525, SG3524 Calculator
  • Inverter LC Filter Calculator

People Also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |

Recent Comments

  • Swagatam on 10 LED Tachometer Circuit Diagram
  • Swagatam on How Shunt Regulator TL431 Works, Datasheet, Application
  • Göran on 10 LED Tachometer Circuit Diagram
  • SA on How Shunt Regulator TL431 Works, Datasheet, Application
  • Swagatam on Adjustable 0-100V 50 Amp SMPS Circuit

Company

  • Privacy Policy
  • Cookie Policy
  • About Me
  • Contact
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap

Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Quora
  • Stack Exchange
  • Linkedin
  • © 2025 · Swagatam Innovations