• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Contact | Calculators-online
You are here: Home / Audio and Amplifier Projects / Guitar Distortion Generator Preamplifier Circuit




Guitar Distortion Generator Preamplifier Circuit

Last Updated on November 25, 2023 by Swagatam Leave a Comment

Distortion and overdrive are types of audio signal enhancement that are employed to change the tone of amplified electric musical instruments like guitars.

Table of Contents
  • How the Guitar Distortion Circuit Works
  • How to Test

Typically, this is accomplished by increasing the gain of the instrument, which results in a "fuzzy," "snarling," or "grinding" tone.

Depending on the type and degree of distortion used, the effects change the guitar sound by clipping the signal.

This is done by forcing it well beyond its peak value, which shears off the signal waves, introducing sustain, harmonic and inharmonic overtones, and creating a pressurized sound that is commonly termed as "warm" and "dirty."

When a distinction is made, distortion is a more severe form of the sound than overdrive. The phrases distortion and overdrive are frequently used synonymously.

Intense distortion known as "fuzz" was first produced by guitarists using a preamp with wrongly adjusted gain.

In this article I have explained a simple electronic guitar distortion preamp circuit, which can be used to inject the intended distorted effect into a guitar sound.

How the Guitar Distortion Circuit Works

The Guitar Preamp Distortion Box schematic is shown in the figure below. In a typical common emitter design, transistor Q1 has a gain of 24 dB and is a low noise transistor.

warning message: electricity is dangerous, proceed with caution
guitar distortion circuit

With this type of gain, the guitar music is amplified to a range which can operate the next stage. The next stage is supplied to the differential BJT pair of Q2 and Q3, which is biased as a limiter.

R5 and C3 comprise the RC network, which serves a variety of purposes.

One benefit is that the AC signal at the base of Q3 is low-pass filtered, allowing the differential pair to obtain its DC bias from the output of Q1 instead.

The network additionally offers a base offset between Q2 and Q3 of around 30 mV.

This is essential for generating a greater proportion of even harmonics at low signal amplitudes.

Finally, when power is initially switched ON, the RC network induces Q3 to switch on steadily.

Because the Preamp would probably be turned on and off while hooked into the guitar amp, this keeps turn-on transients from getting to the output, which is crucial.

The circuit's input and output AC signals are coupled by the capacitors C1 and C2.

By providing power for a brief period of time before switching to audio, bypass capacitor C3 regulates the battery voltage and avoid turn-off transients.

R7 is selected is kept small in value, in order to balance the levels of the "on" and "off" signals and to cut down on distortion in the signal route between the device and the amplifier.

How to Test

Turn on the power after connecting the distortion circuit to a guitar and an amplifier.

Adjust the amp's volume and the circuit's volume to produce a clear, largely undistorted guitar sound.

Then pump up the guitar volume level until the distortion also gets louder.

Here, you might need to dial down the amp volume a bit. Play an open string while briefly turning the distortion circuit on and off.

The loudness in both stages should be identical, and the transition should be silent and seamless.

Once you complete the above settings, you're prepared to rock and roll, or play anything you would want with with your guitar strings.

However, you must first attach the circuit board to the guitar body. In the article's prototype, the board was attached to the guitar body using a dab of silicone sealant.

However, there are other approaches you might want to try. If you want to follow suit, be sure to operate in a space that is well-ventilated.

Additionally, wait about 24 hours after applying the glue before covering the enclosure with a lid because while the glue cures, fumes are released that might harm the electronic parts.

After experimenting with the equipment for a period, you might be happy to discover that the distortion preamp circuit causes very slight distortion, when your guitar volume is trimmed down.

However, the distortion level might start sounding more like a swarm full of bees once you increase the volume up.

You'll also like:

  • 1.  FM Signal Booster Circuit with Adjustable Gain
  • 2.  6 watt Audio Amplifier Circuit Using TDA1011
  • 3.  Modify Human Speech with this Digital Voice Changer Circuit
  • 4.  ISD1820 Voice Recording IC Datasheet, Circuit Diagram
  • 5.  75 Watt Power Amplifier Circuit
  • 6.  Low Pass Filter Circuit for Subwoofer

Filed Under: Audio and Amplifier Projects Tagged With: Distortion, Generator, Guitar, Preamplifier

About Swagatam

I am an electronics engineer and doing practical hands-on work from more than 15 years now. Building real circuits, testing them and also making PCB layouts by myself. I really love doing all these things like inventing something new, designing electronics and also helping other people like hobby guys who want to make their own cool circuits at home.

And that is the main reason why I started this website homemade-circuits.com, to share different types of circuit ideas..

If you are having any kind of doubt or question related to circuits then just write down your question in the comment box below, I am like always checking, so I guarantee I will reply you for sure!

Previous Post: « LED Light Circuit for Street Vendors, Hawkers, Shopkeepers
Next Post: DC Power Controller Circuit »

Reader Interactions

Need Help? Please Leave a Comment! We value your input—Kindly keep it relevant to the above topic! Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

circuit simulator image

Subscribe to New Posts




Categories

  • Arduino Projects (89)
  • Audio and Amplifier Projects (132)
  • Automation Projects (17)
  • Automobile Electronics (101)
  • Battery Charger Circuits (83)
  • Datasheets and Components (104)
  • Electronics Theory (143)
  • Free Energy (37)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (19)
  • Health related Projects (25)
  • Home Electrical Circuits (12)
  • Indicator Circuits (14)
  • Inverter Circuits (88)
  • Lamps and Lights (142)
  • Meters and Testers (69)
  • Mini Projects (46)
  • Motor Controller (64)
  • Oscillator Circuits (27)
  • Pets and Pests (15)
  • Power Supply Circuits (108)
  • Remote Control Circuits (50)
  • Security and Alarm (64)
  • Sensors and Detectors (101)
  • Solar Controller Circuits (59)
  • Temperature Controllers (42)
  • Timer and Delay Relay (49)
  • Transmitter Circuits (29)
  • Voltage Control and Protection (39)
  • Water Controller (36)




Other Links

  • Privacy Policy
  • Cookie Policy
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap




People also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |

Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Quora
  • Stack Exchange
  • Linkedin



  • Recent Comments

    • Swagatam on How Shunt Regulator TL431 Works, Datasheet, Application
    • SA on How Shunt Regulator TL431 Works, Datasheet, Application
    • Farmtech on Free Energy Generator Circuit – The N-Machine
    • Nitesh Agrawal on How to Design Simple LED Driver Circuits
    • Swagatam on How to Design Simple LED Driver Circuits

    © 2025 · Swagatam Innovations