• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Contact | Calculators-online
You are here: Home / Audio and Amplifier Projects / Listen to Wildlife and Insects with this Circuit

Listen to Wildlife and Insects with this Circuit

Last Updated on April 2, 2022 by Swagatam 2 Comments

In this post I have explained a simple circuit idea which can be used for listening to the amplified sounds of insects and bugs in gardens, trees, or any deserted, quite backyards.

Table of Contents
  • Basic Requirements
  • Housing for the MIC
  • Circuit Description

Listening to the noises of outdoor wildlife may be a genuine auditory delight as well as a signal of impending danger. When it comes to listening in on the plethora of insects that reside in our yards, gardens, and trees, bird sounds aren't the only player in town. Our tiny little neighbors noises can give a sonic picture of what's going on in their habitat.

By Larry Hillman

Basic Requirements

During the day, when everything is calm and the birds are cheerfully singing, we can almost be certain that everything is normal; nevertheless, when the song ceases and quiet reigns, it is a good indication that something has changed.

The melody of crickets and other bugs at night typically implies that everything is OK, at least until they cease.

You could love hearing those noises with a minimal amount of electrical devices, the majority of which could be simply constructed.

To begin, an appropriate microphone - one that is calibrated over a certain audio pick-up application - is necessary.

Secondly, you'll need an amplifier with enough gain to boost the audio to a suitable listening volume, and also one with a strong enough output to drive either headphones or a speaker.

These are the only materials required to listen in on our wildlife buddies.

Housing for the MIC

Your main focus would be on creating an appropriate housing for the microphone so that it performs optimally in capturing up the desired noises while suppressing the others.

Precision is not feasible in this region; nevertheless, much can be done to enhance practically any microphone's fundamental pick-up selectivity. Because the sound level from our small insect buddies is sometimes several times lower than the surrounding sounds, the microphone setup is our first priority.

For the sound pick-up element, a tiny, affordable electret condenser microphone, which is obtainable from nearly any electronics retailing market, is an excellent option. It just costs approximately 1 dollars and has a diameter of 2.2 mm.

Figure 1 below depicts our basic microphone housing, which is intended to provide some directivity while also reducing ambient noise.

warning message: electricity is dangerous, proceed with caution
mic encosure insode soft pipe construction

The microphone element is enclosed in a 1 to 1/2 inch length of lightweight plastic pipe, having silicone rubber filling the region behind the microphone.

The precise sizes are unimportant. The objective is to provide certain amount of directivity to the front of the microphone while isolating the rear.

Let's investigate a basic amplifier circuit now that we have a working pick-up device.

Circuit Description

The LM386 IC op-amp is still as good now as it was when it originally appeared several decades ago, and it is used in our first amplifier circuit in Fig. 2 below.

listen to wildlife

A section of shielded microphone wire connects the electret to the amplifier circuit. Make the cable length as little as feasible in case the microphone is used outdoors with the amplifier indoors.

The input of the amplifier is identical to that of an op-amp, comprising inverting and non-inverting inputs, a single output optimized to operate low impedance loads, and a gain adjust function.

Either inputs could be linked to circuit ground, resulting in a ground-referenced input. The amp operates on a 4 to 12 volt power supply and uses just under 30 mWs when not in use.

The maximal dissipation of the device is 660 mW. The only piece of advise I have for the amplifier's architecture is to keep the component lines short and the output wiring and components isolated from the input.

When utilizing S2's high gain level, carelessness would only produce creaks and squeaks. It's not easy to cope with, so try your best.

Sidenote: The above circuit can be also applied as a sensitive hearing aid circuit

You'll also like:

  • 1.  Tuned Radio Frequency (TRF) Receiver Circuits
  • 2.  Using Electret Microphone on Computer PC
  • 3.  Prevent Amplifier Fuse from Blowing During Power Switch ON
  • 4.  60 Watt Amplifier Circuit
  • 5.  Parametric Equalizer Circuit
  • 6.  10 Useful Active Filter Circuit Diagrams Explored

About Swagatam

I am an electronics engineer with over 15 years of hands-on experience. I am passionate about inventing, designing electronic circuits and PCBs, and helping hobbyists bring their projects to life. That is why I founded homemade-circuits.com, a website where I share innovative circuit ideas and tutorials. Have a circuit related question? Leave a comment.... I guarantee a reply!

Previous Post: « Different Types of UPS systems – Explained
Next Post: Monitoring 220V AC Load Current using Current Transformer [Circuit Diagram] »

Reader Interactions

Comments

  1. Michael Buckingham says

    April 27, 2022 at 11:53 pm

    An outdoor event here (British Columbia) had a board made up that has 8 bird sounds and the kid has to hit the right button to identify the correct name with the sound.
    I don’t know what this circuit is called, hopefully there is a chip that can do this. I would love to make one for our organisation events (keeps.org)
    your thoughts please, thank you, Michael Buckingham

    Reply
    • Swagatam says

      April 28, 2022 at 1:19 pm

      Sounds very interesting. I will try to look for the chip, if I happen to find it, will update the circuit design here for you!

      Reply

Need Help? Please Leave a Comment! We value your input—Kindly keep it relevant to the above topic! Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar




Subscribe to New Circuits

Categories

  • Arduino Projects (87)
  • Audio and Amplifier Projects (132)
  • Automation Projects (17)
  • Automobile Electronics (101)
  • Battery Charger Circuits (83)
  • Datasheets and Components (104)
  • Electronics Theory (143)
  • Free Energy (37)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (19)
  • Health related Projects (25)
  • Home Electrical Circuits (12)
  • Indicator Circuits (14)
  • Inverter Circuits (87)
  • Lamps and Lights (142)
  • Meters and Testers (69)
  • Mini Projects (46)
  • Motor Controller (64)
  • Oscillator Circuits (27)
  • Pets and Pests (15)
  • Power Supply Circuits (108)
  • Remote Control Circuits (50)
  • Security and Alarm (64)
  • Sensors and Detectors (101)
  • Solar Controller Circuits (59)
  • Temperature Controllers (42)
  • Timer and Delay Relay (49)
  • Transmitter Circuits (29)
  • Voltage Control and Protection (37)
  • Water Controller (36)




  • Privacy Policy
  • Cookie Policy
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap




People also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |

Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Quora
  • Stack Exchange
  • Linkedin



  • © 2025 · Swagatam Innovations