• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Contact | Calculators-online
You are here: Home / Solar Controller Circuits / Super Capacitor Hand Cranked Charger Circuit

Super Capacitor Hand Cranked Charger Circuit

Last Updated on March 15, 2019 by Swagatam 7 Comments

In this post I have explained a simple super capacitor hand cranked charger circuit using bridge rectifier which may be applied for charging a bank of super capacitors through any suitable hand cranked generator machine. The idea was requested by Mrs. Janet

Table of Contents
  • Prevent Reverse Discharge in Super Capacitors
  • Circuit Schematic
  • The Design
  • How to Solder Bridge Rectifier with Super Capacitor
  • Solving the Circuit Queries

Prevent Reverse Discharge in Super Capacitors

For a DIY project I bought a 24 V, 25 Farad Super capacitor Module sometimes ago here:

warning message: electricity is dangerous, proceed with caution
super capacitor bank

But I need to stop the reverse polarity that always occur whenever I'm charging it with an hand crank 24Vdc generator.

Please Swag, what exact Diode should I use? How do I get the positive and Negative terminals of the Diode in order to solder correctly the Diode to the Super-cap Module?

Thank you in advance.

P.S: please if possible, give me a pictorial guide.
Thank you a Million times.

Circuit Schematic

simple super capacitor charger using bridge rectifier

The Design

The solution to the proposed super capacitor hand cranked charger circuit is very simple, it's by using a bridge rectifier for the required DC conversion across both the cycles of the AC.

As we all know a bridge rectifier is configured in such a way that the connected diodes become equipped for rectifying an AC through both half cycles applied across it.

The preferred hand cranked alternator device also acts like an AC generator wherein the forward motion of the cranking produces a forward or a positive current while the retracting action in the device does the opposite and develops a negative current across its outputs.

Therefore if the wires of the hand cranked generator or any generator are connected directly with a filter capacitor which is a super capacitor in the present case would charge the capacitors during the first motion and immediately discharge the capacitor during the reverse motion of the cranking, resulting in a net zero charge inside the capacitors.

When a bridge rectifier is connected across such a generator as shown in the diagram, both the positive and the negative currents across its output are appropriately transformed into a single polarity voltage which helps to charge the super capacitors effectively without inflicting any loss across the capacitors.

How to Solder Bridge Rectifier with Super Capacitor

Thank you again for keeping up with your promise.

But please I am sorry, I do not fully comprehend the know-how on how to solder the diode in series as you Pictured it.

What exactly it is that I do not know is how to get the positive and Negative terminals of the Diode in order to solder correctly the Diode to the Super-cap Module?

Also, when I get the positive and negative terminals, will I solder the Positive leg of the Diode to the Positive terminal of the super cap and do the same to the Negative terminals?

Please forgive me for my silly questions.

P.S: In the datasheet I saw Max. Reverse Current:1A and Max. Forward Current:30A
What does this mean?

My Super Capacitor Maximum Output Current is 5A and Voltage is 24V. How many of the Diodes in the above link will I need to solder on to my Super cap?

Is it possible to Simultaneously charge super capacitor and Discharge it? Is such practice safe?

Thanks.

Solving the Circuit Queries

I have attached the diagram in pictorial form, please check it out

How to connect bridge rectifier with super capacitor

The reverse current will matter only in case if the red/black wires are reversed while connecting with the super capacitor.... the capacitors will get damaged if the current in this condition exceeds 1 amp.


The 30 amp suggests the max current tolerance in normal conditions as given in the attached image.

But still it will matter only if the voltage from the generator tends to exceed the max voltage rating of the super capacitor..

If it remains within the capacitors voltage range the forward current tolerance becomes immaterial and may be ignored....so please confirm the generator's maximum voltage, it must not be more than 24 V for the indicated super capacitor module.

The diodes in the bridge could be 1N5408 for ensuring complete safety to the system.

The super capacitor can be charged/discharged at will thousands of times irrespective of any precautions or care.

You'll also like:

  • 1.  Optimizing Grid, Solar Electricity with Inverter
  • 2.  How to Configure a Solar Panel System – Living of the Grid
  • 3.  Homemade Solar MPPT Circuit – Poor Man’s Maximum Power Point Tracker
  • 4.  Solar Drip Irrigation Circuit for Indoor Gardens
  • 5.  Solar Panel Enhancer Using Solar Mirror Concept
  • 6.  Solar Charge Controller for 100 Ah Battery

Filed Under: Solar Controller Circuits Tagged With: Capacitor, Charger, Cranked, Hand, Super

About Swagatam

I am an electronics engineer and doing practical hands-on work from more than 15 years now. Building real circuits, testing them and also making PCB layouts by myself. I really love doing all these things like inventing something new, designing electronics and also helping other people like hobby guys who want to make their own cool circuits at home.

And that is the main reason why I started this website homemade-circuits.com, to share different types of circuit ideas..

If you are having any kind of doubt or question related to circuits then just write down your question in the comment box below, I am like always checking, so I guarantee I will reply you for sure!

Previous Post: « 3 Automatic Fish Aquarium Light Optimizer Circuits
Next Post: How to Convert a Low Power Inverter to a High Power Inverter »
Subscribe
Notify of
guest


guest
7 Comments
Inline Feedbacks
View all comments

Primary Sidebar

circuit simulator image

Subscribe to get New Circuits in your Email

Categories

  • Arduino Projects (90)
  • Audio and Amplifier Projects (132)
  • Automation Projects (17)
  • Automobile Electronics (101)
  • Battery Charger Circuits (83)
  • Datasheets and Components (106)
  • Electronics Theory (143)
  • Free Energy (37)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (19)
  • Health related Projects (25)
  • Home Electrical Circuits (12)
  • Indicator Circuits (15)
  • Inverter Circuits (89)
  • Lamps and Lights (142)
  • Meters and Testers (71)
  • Mini Projects (47)
  • Motor Controller (64)
  • Oscillator Circuits (28)
  • Pets and Pests (15)
  • Power Supply Circuits (108)
  • Remote Control Circuits (50)
  • Security and Alarm (64)
  • Sensors and Detectors (103)
  • Solar Controller Circuits (59)
  • Temperature Controllers (42)
  • Timer and Delay Relay (49)
  • Transmitter Circuits (29)
  • Voltage Control and Protection (40)
  • Water Controller (36)

Other Links

  • Privacy Policy
  • Cookie Policy
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap

People also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |

Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Quora
  • Stack Exchange
  • Linkedin
  • Recent Comments

    • Swagatam on TV Antenna Amplifier Circuit Diagram to Boost TV Signal Reception
    • Swagatam on TV Antenna Amplifier Circuit Diagram to Boost TV Signal Reception
    • Swagatam on Mains 220 V AC Line Filter Circuit for Transient Suppression
    • Swagatam on 600 V DC Voltage Regulator Circuit Module
    • Swagatam on Car Tank Water Sensor Circuit

    © 2025 · Swagatam Innovations