• Skip to main content
  • Skip to primary sidebar

Homemade Circuit Projects

Need circuit help? Post them in the comments! I've answered over 50,000!

Blog | Categories | About | Contact | Calculators-online
You are here: Home / Remote Control Circuits / How to Make a Remote Control Circuit from a Remote Bell

How to Make a Remote Control Circuit from a Remote Bell

Last Updated on July 3, 2019 by Swagatam 8 Comments

The proposed remote control circuit idea can be used for controlling any electrical gadget within a range of 100 meters.

Table of Contents
  • How the Circuit is Supposed to Work
  • Circuit Diagram
  • Modifying the Receiver (Rx) of the Remote Bell
  • Parts List

How the Circuit is Supposed to Work

Since the idea here is to modify an existing circuit of a remote bell unit, becomes super easy without any complications.

However the construction part does require the involvement of electronic assemblies so this project may not be considered entirely a layman’s project. We all have seen and probably used remote bell gadget in our homes.

The device is basically a wireless RF receiver and a transmitter set which can be used for producing alarm sounds remotely for calling or indication proposes.

These gadgets are pretty effective with their functions and the specified operations are done efficiently across a considerable distance.

The Chinese made remote bell units are best suited for the proposed project. Basically, when the transmitter of the remote bell is pressed, it sends a strong RF signal over a radial distance of approximately 100 meters.

The receiver unit positioned anywhere within this limit instantly plucks the trigger and switches the in built musical bell, sounding the alarm.

The trigger may last for a few moments even after the transmitter is switched OFF. The only feature that we are interested in is the effective transmission and receiving of the RF signals across the said distance.
If we are able to mod the receiver part of the unit so that the received trigger can be used to operate a relay instead of the usual alarm, our job is done.

However before we indulge into the modification process, it would be necessary to make the Flip Flop circuit first, which would be later on required to be integrated with the receiver set of the remote bell.

The flip flop section is a very simple configuration consisting of just a single IC and a few other passive components.
The entire circuit may be buikt over a small general purpose board with the help of the shown schematic.

Circuit Diagram

warning message: electricity is dangerous, proceed with caution

 

Modifying the Receiver (Rx) of the Remote Bell

On opening the cover of the remote bell receiver unit, the following things may be traced out for commencing the modding process:

You will find a small speaker connected via a couple of wires which terminate from the circuit board of the unit.

Just cut-of the wires from the speaker, remove the entire circuit from its housing and screw it inside a new housing, which should be relatively bigger in size so that it can accommodate the flip flop section, the transformer power supply section and also the relay assembly.

After locating the negative wire out of the two speaker wires, integrate them to the flip flop circuit appropriately as shown in the figure.

Once the connections are made as per the schematic, check the system by powering the unit and by making a few triggers via the transmitter module.

The relay can be seen toggling in response to each subsequent triggers made by the transmitter module.

Your RF remote control circuit is ready and may be used for controlling any electrical gadget that you may prefer, wirelessly, across a radial distance of around 100 meters.

Parts List for the Circuit Diagram The following listed parts will be required for making the above explained RF remote control circuit's flip flop section:

Parts List

R3 = 100 ohms,

R2 = 100K,

R4 = 4K7,

R5 = 10K,

C1, C2, C4= 22uF/25V,

C6 = 4.7uF/25V,

C3 = 0.1, CERAMIC,

C5 = 1000uF/25V,

T1 = BC557B

T2 = BC547B,

ALL DIODES ARE = 1N4007,

L1 = 50 turns of 30 SWG super enameled copper wire wound over a any ferrite material.

IC1 = 4017,

IC2 = 7805,

TRANSFORMER = 0-12V/500mA,

You'll also like:

  • 1.  Bluetooth Car Ignition Lock Circuit – Keyless Car Protection
  • 2.  Infrared Remote Control Safe Lock Circuit
  • 3.  Remote Controlled Toy Car using 433 MHz Remote Modules
  • 4.  Infrared Remote Controlled Door Lock Circuit
  • 5.  Remote Controlled Fish Feeder Circuit – Solenoid Controlled
  • 6.  Infrared (IR) Motor Remote Control Circuit

Filed Under: Remote Control Circuits Tagged With: Bell, Control, Remote

About Swagatam

I am an electronics engineer and doing practical hands-on work from more than 15 years now. Building real circuits, testing them and also making PCB layouts by myself. I really love doing all these things like inventing something new, designing electronics and also helping other people like hobby guys who want to make their own cool circuits at home.

And that is the main reason why I started this website homemade-circuits.com, to share different types of circuit ideas..

If you are having any kind of doubt or question related to circuits then just write down your question in the comment box below, I am like always checking, so I guarantee I will reply you for sure!

Previous Post: « 2 Simple Infrared (IR) Remote Control Circuits
Next Post: High Voltage Transistors BUX 86 and BUX 87 – Specifications »

Reader Interactions

Comments

  1. Andy Turner says

    November 10, 2020 at 5:50 pm

    Hi Swagatam, You have helped me out with a circuit already, a motion sensing detector circuit that switches off in the day – thanks ! I have a new challenge, how to use a motion detector at the front gate of the house to sound an audible alarm inside the house (wirelessly). The above circuit looks a bit complicated and I don’t have any remote bell circuits hanging around. Any suggestions would be appreciated – Thanks.

    Reply
    • Swagatam says

      November 10, 2020 at 6:58 pm

      Thanks Andy, I think the easiest idea would be to buy a ready-made pair of remote bell Tx/Rx units, then couple the Tx (transmitter) unit’s bell switch wires with the relay contacts of your proximity detector circuit. Once this is done, each time the proximity relay clicks will result in an alarm sound from the Rx unit of the remote bell.

      Reply
  2. Norman says

    January 17, 2018 at 10:56 pm

    I have place all the new components on the shematic, I do not find the place for R1 : 100 ? I will send you the new shematic after.

    Norman

    Reply
    • Swagatam says

      January 18, 2018 at 9:31 am

      sorry R1 is mistakenly included in the parts list, please ignore it as it is not there in the schematic, I’ll correct the parts list soon

      Reply
  3. sukhidec says

    October 31, 2016 at 9:56 am

    From where can i get L1 or will it work without L1

    Reply
  4. Amlan says

    January 20, 2014 at 8:14 am

    brother can i use all capacitor rated 50v??

    Reply
    • Swagatam says

      January 21, 2014 at 4:53 am

      yes that will do, even twice the value of the supply voltage will be safe.

      Reply
  5. Swagatam says

    October 16, 2013 at 2:12 pm

    it's the positive supply rail of the radio where the + of the battery or the AC/DC adapter is connected for powering the radio

    Reply

Need Help? Please Leave a Comment! We value your input—Kindly keep it relevant to the above topic! Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

circuit simulator image

Subscribe to get New Circuits in your Email



Categories

  • Arduino Projects (89)
  • Audio and Amplifier Projects (132)
  • Automation Projects (17)
  • Automobile Electronics (101)
  • Battery Charger Circuits (83)
  • Datasheets and Components (105)
  • Electronics Theory (143)
  • Free Energy (37)
  • Games and Sports Projects (11)
  • Grid and 3-Phase (19)
  • Health related Projects (25)
  • Home Electrical Circuits (12)
  • Indicator Circuits (14)
  • Inverter Circuits (88)
  • Lamps and Lights (142)
  • Meters and Testers (69)
  • Mini Projects (46)
  • Motor Controller (64)
  • Oscillator Circuits (28)
  • Pets and Pests (15)
  • Power Supply Circuits (108)
  • Remote Control Circuits (50)
  • Security and Alarm (64)
  • Sensors and Detectors (102)
  • Solar Controller Circuits (59)
  • Temperature Controllers (42)
  • Timer and Delay Relay (49)
  • Transmitter Circuits (29)
  • Voltage Control and Protection (40)
  • Water Controller (36)



Other Links

  • Privacy Policy
  • Cookie Policy
  • Disclaimer
  • Copyright
  • Videos
  • Sitemap

People also Search

555 Circuits | 741 Circuits | LM324 Circuits | LM338 Circuits | 4017 Circuits | Ultrasonic Projects | SMPS Projects | Christmas Projects | MOSFETs | Radio Circuits | Laser Circuits | PIR Projects |



Social Profiles

  • Twitter
  • YouTube
  • Instagram
  • Pinterest
  • My Facebook-Page
  • Quora
  • Stack Exchange
  • Linkedin


  • Recent Comments

    • Swagatam on How to Make Dog Barking Preventer Circuit using High Frequency Deterrence
    • Swagatam on How to Make Dog Barking Preventer Circuit using High Frequency Deterrence
    • Swagatam on Dual Battery Charger Circuit with Isolator
    • suat kaleli on How to Make Dog Barking Preventer Circuit using High Frequency Deterrence
    • Swagatam on 9 Simple Solar Battery Charger Circuits

    © 2025 · Swagatam Innovations