A couple of simple yet efficient 220V operated transformerless 50V adjustable solid-state power supply circuit using a single IC SR087 is discussed in the following article. The design does not depend on high value capacitors or inductors and yet is capable of delivering 100mA current to the attache load.
Circuit#1: Main Features and Board Layout
The Main features of this power supply using the IC SR087 are:
High efficiency without incorporating inductors. Does not require high voltage capacitors for mains current dropping. Can be used with 120V AC as well as 220V AC inputs Output adjustable from 9V to 50VDC Has an internal soft stat circuitry Stand by consumption is less than 200mW
The Supertex SR087 is an transformerless switching regulator chip specially designed to operate directly from a rectified 220V or 120V AC line.
The principle of operation is to switch ON a pass transistor each time the rectified AC reaches under the set output level, and switch it OFF as soon as the output level is sustained at the set level.
A internally set 5V linear regulator offers an additional 5V fixed output from the IC for operating devices requiring strict 5V inputs.
The IC also facilitates an external logic input triggered "disable" feature, which can be used for disabling the circuit when not in usee and keep the system in the standby mode.
WARNING! Galvanic isolation is not included in the design. Life threatening voltages and shocks may be floating when switched ON to the AC line. The designer employing the SR087 must ensure proper safety measures are employed to protect the end user from fatality.
The circuits described here are not guaranteed to fulfill surge and EMI conduction requirements.
The working of these circuits might differ depending on a given application. The designer is advised to implement tests to verify compliance with the laid down world standards and regulations.
VIN - Should be connected across a 120/230VAC line. The AC input stgae of the circuit is safeguarded from surge currents by a 275V metal oxide varistor (MOV) and also a 1.25A
Never use a transformer at the input line. The high inductance might generate an inductive back EMF, overloading the
MOV and destroying it. Please note that the proposed 50V adjustable transformerless power supply is not design to operate through the supply input from a square wave uninterruptible which are also usually referred to as “modified sine wave”.
GND - This is the circuit common line. And because the circuit does not offer a galvanic isolation from mains 220V or 120V, connecting this common line to an earth-grounded equipment,
(such as an oscilloscope), could cause a short circuited the AC line, leading to an instant damage to the circuit or even the equipment in use.
You may also want to note that GND may be at a raised voltage level with respect
to earth ground, even while the AC input is switched off. Be cautioned about this!
VOUT - This refers to the main output of the circuit stage.
The SR087 IC is designed to regulate the peak output voltage, and not the average value, therefore the
average voltage will show a tendency to decline when a load is attached.
VOUT can be adjusted from 9.0 to 50V by changing the value of R1 as per the formula given in the circuit diagram
VREG - It is the fixed 5V regulated output, from the IC. Since this output is derived from the 50V line any load on VREG might cause an equivalent current drop across VOUT.
VREG will require at least 4.0V of headroom
to generate the 5V, that is a minimum of 9V at VOUT.
Since the IC is typically a linear regulator, the SR087 will dissipate
power as curent on VREG output or VOUT goes up to around 460mW at 60mA.
ENABLE - If a logic low (<0.2V) is applied on this pinout it enables Q1
switching and the VOUT switched ON.
However a logic
high (>0.75 • VREG) on this pinout quickly disables Q1
, shutting the VOUT supply and also the VREG output.
However, if an external voltage exists across VOUT terminals in the disabled state, VREG will continue to function allow a 5.0V to be generated across the specified terminals.
The ENABLE input is equipped with 20kΩ pull-down resistor. In case it's not required or unused, it could be simply left unconnected or connected to ground.
12V, 5V Solid-State Power Supply Using IC LR645
In the following second single IC based solid-state design we study how the mains voltage is controlled to 12V and 5V using just a single IC LR645G and some other supportive ordinary active semiconductors.
In one of my earlier posts I provided a similar circuit but it utilized a high voltage capacitor for dropping the mains voltage to lower usable levels.
Thanks to Supertex ic. for providing us with this wonderful little chip LR645G, which single handedly controls any voltage between 24 and 270 V AC and produces DC voltages below 15 volts at the output, which becomes ideally suitable for operating sensitive, compact electronic circuits.
The best part of the circuit is that it does not incorporate any bulky of heavy components like a transformer or non polar high voltage capacitors.
Though we all know the simple way of constructing transformerless power supply units using high voltage capacitors, these high voltage capacitors have one big drawback.
At switch ON, these caps allow high surge inputs to pass through them and also intermediate transients become unstoppable with these devices.
The drawback can cause havoc with any electronic circuit that may be connected to such power supply configurations.
Using LR645G the above threat becomes absolutely nullified. The maximum current available from this device is quite low, around 3 mA, however that's never a problem, because the current can be shot up to 150 mA, through a simple addition of an fet DN2540N5 in the circuit.
The figure shown above is a classic solid-state circuit set up of a 12V and 5V transformerless power supply circuit which can provide outputs of 15 volts and 5 volts.
15 volts is available just at the junction of the output of LR645 and the input of Ic 7805.
If the 5 volt option is not required, the configuration around the 5 volt regulator can be just eliminated, which makes the circuit yet simpler and compact.
How the Circuits Works
In short the circuit diagram may be understood in the following manner:
- The high voltage AC mains is rectified by the bridge configuration using four diodes at the input.
- The rectified voltage is smoothed by the filter capacitor introduced just after the bridge network.
- The rectified, filtered high voltage is fed to the IC LR645LG, which effectively reduces the voltage to 15 volts at 3 mA.
- The FET pulls the 3 mA current output to 150 mA and feds it to the next stage which incorporates the 5 volt regulator stage.
However one big drawback of not incorporating a transformer is the DANGER of high voltage shock that actively hangs with all the naked points of the circuit.
Therefore extreme caution must be exercised while building and testing this circuit and other attached circuits.
Diodes - 1N4007
Input Capacitor - 4.7uF/400V,
Output Capacitors are 1uF/25V
ICs are LR645LG and 7805,
FET - DN2540N5
"Howdy friend! Are you a newcomer and looking for personalized help? Please feel free to use the comment box below for posting your queries, and get guaranteed replies within an hour!"