The idea could be appropriately implemented for generating an RGB scrolling alphabet effect.
The main control circuit for the proposed RGB LED alphabet chaser circuit can be witnessed below, consisting of 3 Johnsons decade counter 4017 ICs and a clock generator IC 555.
Let's first try to understand the role of this stage and how it's supposed to carry out the running RGB LED effect.
The 555 IC astable clock generator stage is included for generating the sequencing pulse for the 3 ICs, whose pin14 can be seen combined and joined with the output of the IC 555 for the required triggering.
When power is switched ON, the 0.1uF capacitor connected with pin15 of the IC1 4017 resets this IC such that the sequencing is able to begin from pin3 of this IC, that is from pin3>2>4>7>10...and so on in response to every clock pulse at its pin14.
However at the onset, when it's reset by the 0.1uF cap, except pin3 all its output pins become low including its pin11.
With pin11 at zero, the pin15 of IC2 is unable to get a ground potential and therefore it stays disabled, and the same happens with IC3 as well...so IC2 and IC 3 stay disabled for the moment, while IC1 begins sequencing.
Now as a result IC1 outputs start sequencing producing a sequencing (shifting) "high" across its output pins from pin3 towards pin11, until finally the sequence high reaches pin11.
As soon as pin11 becomes high in the order, the pin13 of IC1 also becomes high which instantly freezes IC1, and the high logic at pin11 gets locked....the IC now remains in this position unable to do anything.
However the above triggers the associated BC547, which instantly enables IC2 which now imitates IC1 and starts sequencing from its pin3 towards pin11, one by one....and quite identically as soon as the pin11 of IC2 goes high, it likewise gets locked and enables IC3 to the repeat the procedure.
IC3 also follows the footprints of the earlier ICs and as soon as the sequencing logic high reaches its pin11, the logic high is transferred to pin15 of IC1....which instantly resets IC1 restoring the system back to its original form, and IC1 yet again begins the sequencing process, and the cycle keeps repeating itself.
We learned and understood how exactly the above RGB controller circuit is supposed to function with the stipulated sequencing procedures, now it would be interesting to see how the sequencing outputs from the above circuit may be used with a compatible driver stage for implementing the intended RGB LED scrolling over a selected set of alphabets.
All transistors are 2N2907
All SCRs are BT169
SCR gate resistors and PNP base resistors are all 1K
LED series resistors will be as per the LED current.
The above image depicts the RGB driver stage, we can see 8 numbers of RGB LEDs utilized (in the shaded square boxes), this is because the discussed 4017 Circuit is designed to produce 8 sequential outputs and therefore the driver stage too accommodated 8 numbers of these LEDs.
To learn more about RGB LEDs you can refer to the following related posts:
In the design SCRs can be seen included at the negative ends with each of the LEDs and also PNP transistors over the positive ends of the LEDs.
Basically the SCRs are positioned for latching the LED illumination while the PNP is connected exactly for the opposite that is for breaking the latch.
The sequencing or rather the typical alphabet scrolling effect is implemented by assigning the various LEDs in the following pattern:
All the red LEDs from the RGB modules can be seen connected with the IC1 outputs, the green LEDs with the IC2 outputs and the blue LEDs with the IC3 outputs, via the corresponding SCR gates. When the SCRs are triggered the relevant LEDs become illuminated in a chasing sequence.
As explained in the earlier section, the IC1, IC2, and the IC3 are rigged in a way that the ICs respond in a cascaded fashion, wherein IC1 begins sequencing first, followed by IC2 and then IC3, the cycle then keeps repeating itself.
Therefore when IC1 begins sequencing all the red LEDs in the respective RGB modules get triggered and latched.
When IC2 is enabled with the sequencing it starts illuminating and latching the green LED in the array via the concerned SCRs, but simultaneously also breaks the RED led latch via the associated PNP transistors. The same is carried out by the IC3 outputs but this time for the green LEDs in the RGB modules,
When green LED sequencing elapses it's yet again replaced by the IC1 for processing the red LEDs, and the entire procedure starts simulating a dazzling RGB LED scrolling effect.
The above shown animated simulation provides an exact replica of the scrolling of the LEDs that may be expected from the proposed design.
The indicated running white spots on the SCR gates indicate the triggering and the execution of the latching function by the SCRs, while the PNP base white spots indicate the breaking of the relevant SCR latches.
Single LEDs are shown in the sequence, but depending on the supply voltage more numbers of series LEDs could be inserted within each of the RGB channels. For example with a 12V supply 3 LEDs may be incorporated on each of the channels, with 24V this may be increased to 6 LEDs on each of the channels.
How to configure the above effect for creating a running or scrolling RGB LED alphabets
The above example shows a classic RGB scrolling alphabet simulation using the above explained circuit.
Each alphabet can be seen wired with the red, green and the blue LEDs from the 8 RGB LED modules.
The series parallel connections can be a little complex, and might require some experience and skill, the following articles can be studied for understanding the calculations involved for wiring LEDs in series and parallel:
Many different innovative patterns can be designed and implemented using ones own creative imaginations and by wiring the RGB LEDs appropriately across the sequence.