The only electronic website that replies to every comment, and addresses all circuit related issues.

Illuminating four 1 watt LEDS with 1.5V Cell - Joule thief Circuit

Can you imagine illuminating four numbers of 1 watt LEDs through a a few 1.5V cells? Looks quite impossible. But it can be done simply using a coil of ordinary speaker wire, a transistor, a resistor and of-course a 1.5V pencil cell.

The idea was suggested to me by one the keen followers of this blog Ms. MayaB, here are the details, let's learn them:

FYI, I tried this simple JT using a 40ft. paired speaker wire (24AWG) purchased at dollar store (of course, for $1). 

No torroid, no ferrite rod, just simple air core wound to make it more like a coil (about 3" diameter) and tied the wire with a twistie tie (so that the wire will stay as a coil). 

I used 2N2222 transistor, 510 ohm resistor (found out that is the best with a help of potentiometer) and was able to BRIGHTLY lit four (that is all I had) 1-watt high power LED in series (which requires same amount of current as if it was used for only one LED) using two 1.5V AA batteries (that is 3V power supply). 

Can be used only one 1.5AA but will be dim (of course). I have also added a diode 1N4148 at the transistor's collecter pin just before the LED but can't tell if it increased any brightness. 

Many people have used a capacitor in parallel to the battery claiming it will light the LEDs longer, I have not tested that part yet.

I have read adding a 220uF/50V electrolytic capacitor parallel to the battery would make the lights run longer, adding a 470pF/50V ceramic disc capacitor parallel to resistor will recouple the waste current in the resistor, and adding a 1N4148 diode (it is a switching diode but I don't know how would that effect the brightness) at collector of the transistor before the LEDs in series makes the LEDs brighter. 

I don't have an oscilloscope to check all that effects. However, I would like to use rechargeable batteries instead of regular AA battery and make it self-regulated (or at least semi-self regulated) circuit by adding a calculator solar cell and a mini Joule Thief on a small toroid to keep charging the battery to last much-much longer.  

I indeed need to add a LDR to light the LEDs only at dark and recharge the batteries during the daytime. Your suggestions and ideas are always welcome. Thanks, once again, for your interest.

Feedback from MayaB

Hi Swagatam,
Though it is long known Joule Thief circuit, not something new I discovered but thank you for posting a new article on behalf of me, I appreciated it.


Ps. Over the weekend I hybridized your circuit with the circuit I sent you here and it turned out to be dazzling bright (warning: may blind your eyesight, hehe). 

I used the same speaker wire (mentioned above), a 8050SL transistor, 2.2K resistor (paralled with a 470pf capacitor), one 1W high power LED, a 100uH choke (connected from collector of the transistor to the positive rail of power supply), and 1 diode (1N5822 connected at base of the transitor to the positive rail of the power supply). 

I used two 1.5V (total of 3V) AA batteries for power supply. And btw, a LDR between 2.2K resistor and the negative rail can be added to turn the LED off during the daylight. Unfortunately, could not light more than one 1W LED with 8050SL transistor in this configuration.

Please Share this Post:
  •  Facebook
  •  Twitter
  •  Google+
  •  Stumble


    1. Hi. Mr. Swagatam.
      Good Job

      I was make earliar same type Joule thief Circuit- 7-20mW LED s lighten with 1.2V Nimh Battery.

    2. hi swagatam,same but i didn't use transistors but 9-0-9 1A transformer & 1V5 cell with rotary switch or scratching the wires over the cell create very high V at the output,can lighten 2-3neon bulb. (the switch is homemade,changeover is done by a tiny motor with 6 point)

      i guess there is no heat/resistance loss whole VA directly used for invertion.
      switching is 10~15Hz maximum. is this good to design a -low cost "mechanical switching inverter"?
      and why mains freq always 50~60Hz, what happen if inverter make 230v15HzAC?

      1. Hi Max,

        your circuit is exhibiting a simple inverter principle, it's not a "joule thief" and it won't light up LEDs.

        50Hz is the standard accepted frequency according to which all inductive appliances are designed and calculated, if this frequency is altered all inductive appliances like motors, compressors would fail to operate.

    3. Hello Swagatam, why u said LED won't light up? actually the LED would blown out in this arrangement. i got shock when i touched d secondary.
      mechanical switching is different. rub the wires on 1.5v button cell or 3v and feel the secondary volt!

      Check this out. the circuit said above is from here

      vibration/switching is done by bell circuit
      post a "mech inverter" rather than solid state, to understand -Early Version of Power Inverter.

      1. Hello Max,

        The LED will illuminate but not as efficiently as it would do with a joule thief type of design, and also the 1.5V cell would drain out pretty quickly.

        Your circuit is the most basic form of inverter using an iron core, which have poor efficiency.

    4. What percentage of full illumination of 1 Watt Led, this circuit provides?
      from the pictures, Leds appear to be without heat sink.

      1. Yes the illumination won't be upto the maximum level...


    Please Note: If you find any DEAD link starting with http//, please replace it with for making it visible and alive again.